One System Handling Both Seasons

Heat Pump Repair and Installation in Longview for homes replacing separate heating and cooling equipment or systems that no longer reverse modes

Many single-story ranch homes across the Hawkins Parkway area and Gilmer Road corridor were built with separate furnaces and air conditioners, and a heat pump can replace both pieces of equipment, simplifying the layout and reducing the number of components that require maintenance. EZ Air Solutions repairs and installs heat pumps in Longview after evaluating the home's heating and cooling loads, checking existing ductwork and electrical service, sizing the outdoor and indoor units, setting refrigerant charge, and testing both heating and cooling modes. A properly sized heat pump delivers cool air in summer and warm air in winter without requiring a separate furnace or condenser.


The technician measures the home's square footage, insulation levels, and window area, inspects the duct system for sizing and leaks, verifies that the electrical panel can supply the heat pump's amperage draw, and calculates the tonnage required to meet both heating and cooling demand. A unit that is undersized will struggle to maintain temperature during cold snaps, while an oversized unit will short-cycle and fail to remove humidity in summer, so the load calculation determines the correct capacity before any equipment is ordered.


Schedule a load evaluation to determine whether a heat pump fits your home's heating and cooling requirements.

What the Service Actually Accomplishes

A heat pump installation replaces both the outdoor condenser and the indoor air handler, connects refrigerant lines that carry heat in both directions, wires the reversing valve and defrost controls, and configures the thermostat to switch between heating and cooling modes. The system uses the same refrigerant loop to move heat outdoors in summer and pull heat indoors in winter, which eliminates the need for a gas line, flue, or combustion chamber.


Once the installation is complete, the thermostat switches seamlessly between heating and cooling, the outdoor unit reverses the refrigerant flow when the mode changes, and the air handler delivers warm or cool air depending on the season. You notice that the system maintains steady indoor temperature without operating separate pieces of equipment, and the outdoor unit runs quietly in both modes without grinding or laboring sounds.


The crew removes the old furnace and air conditioner, installs the new heat pump condenser on a level pad, mounts the air handler in the existing plenum or closet, connects refrigerant lines and electrical supply, pulls a vacuum on the line set, releases refrigerant to the manufacturer's specified charge, and tests both heating and cooling operation. The work includes verifying that the reversing valve switches correctly, the defrost cycle activates when frost builds on the outdoor coil, and airflow matches the unit's design specification.

Answers About How the Work Is Done

Homeowners often ask how a heat pump performs during cold weather and whether the system requires backup heat when outdoor temperatures drop.

  • How does a heat pump provide heating when the outdoor temperature is below freezing?

    The refrigerant absorbs heat from the outdoor air even when the temperature is well below freezing, compresses that heat to a higher temperature, and releases it indoors through the air handler coil, using the same process that cools a home in summer but running in reverse.

  • What happens during the defrost cycle when frost builds up on the outdoor coil?

    The heat pump temporarily reverses to cooling mode to send warm refrigerant to the outdoor coil, which melts the frost, and the system switches back to heating mode once the coil is clear, typically within five to ten minutes, while backup heat strips inside the air handler keep warm air flowing during the defrost cycle.

  • Why is proper refrigerant charge more critical for a heat pump than a standard air conditioner?

    A heat pump operates in both heating and cooling modes, and refrigerant charge affects performance in both directions, so an overcharge or undercharge reduces heating capacity in winter and cooling capacity in summer, and the charge must match the line set length and the manufacturer's specification for the outdoor temperature at the time of installation.

  • What should you notice after a heat pump installation is complete?

    The thermostat switches between heating and cooling without requiring manual adjustment, warm air flows from the registers when the system is in heating mode, cool air flows when the system is in cooling mode, and the outdoor unit runs smoothly in both directions without excessive noise or vibration.

  • How does a dual-fuel heat pump differ from a standard electric heat pump?

    A dual-fuel system pairs the heat pump with a gas furnace that takes over when the outdoor temperature drops below the heat pump's efficient operating range, which reduces electric usage during cold weather and provides faster heating recovery, whereas a standard heat pump relies on electric resistance strips for backup heat.

EZ Air Solutions has more than ten years of HVAC experience and sizes every heat pump installation to the home's specific heating and cooling loads. EZ Air Solutions also repairs and installs heat pumps in Gladewater, Marshall, Kilgore, White Oak, and Gilmer. Call (903) 445-7814 to arrange an in-home evaluation and receive a detailed proposal for heat pump installation.